Hypnotic Table

image

Experimenting with new table top designs, utilizing wood lath as usual, I built this end table with spiral top. Don’t stare too long or you might lose your sanity.

image

Advertisements

Leave a comment

Filed under Millwork, tables

Lath dining table commission

image

I’ve been commissioned to build a giant wood lath dining table top, whose final dimensions will be 32” x 6’10. I estimated I need around 200 strips of lath to pull it off. I’ve got most of the stock milled and ready to go, now I just have to lay it all out and glue it up. I’m figuring it’ll take five rounds of gluing to put the whole thing together.  Patience is paramount in a project like this!

Leave a comment

Filed under Millwork, Salvage

Great sign at a local welding shop.

image

Leave a comment

Filed under Uncategorized

Fine Woodworking October 2011

The Lather’s Table I made for the Green Project’s Salvations Contest is in this month’s issue of Fine Woodworking Magazine, featured in the Reader’s Gallery on Page 77.  Fine Woodworking is an awesome magazine to subscribe to if you are into woodworking, and I’m honored to be part of such a prestigious publication this month.   Here’s a scan of the cover and page 77:

1 Comment

Filed under salvations, tables

Lecture and Opening at Lusher High at 2.30 on Friday Sept 23, 2011

If you are in the Uptown area tomorrow September 23rd, and you fancy hearing a lecture on mixed-media art and the merits of anti-specialization, stop by Lusher High: 5624 Freret St at Joseph St. @ 2.30pm.  I’ll do a power point presentation for 45 minutes in room 307 on the varied history and themes of my work, and then on to the gallery reception on the 4th floor where i’ve got some illuminated pieces on display.  It’ll be electric! (dumb pun intended).

Leave a comment

Filed under Insulator Lamps, Photography, Salvage

Lath Console Table

Last week I finished the Lath Console Table I was commissioned to build by a very important client (my dad).  Similar to the Lather’s table I built for the Salvations Design Competition earlier this year, the project relied heavily on salvaged materials and the slow process of lamination (gluing wood together).  The client (pops) wanted me to do a little write up explaining the process of making the table as well as the story behind its inception and parts, so if you are interested in reading that, it is below the pictures.  Overall, I like this table better than the first one I built, though they are a completely different design so direct comparison is difficult.  With this one, i used the skinny part of the wood as the table top surface instead of the fat (how’s that for proper woodworking terminology!) and I really dig the bowling lane/hardwood floor effect it achieves.  I came up with the general design idea for this table while I was building the last one, and after building this one, i’ve got six more designs i’d like to try, all relying on lath.  Oh to have all the free time in the world to build furniture…  Anyway, here are the pics.  Let me know what you think or if you have any ideas for other ways to use lath strips, i’d love to hear them.  P.S. – The first lath table I built is featured in the Reader’s Gallery of the current issue (Sept/Oct) of Fine Woodworking Magazine, page 77 I think.  Checkitout!

This slideshow requires JavaScript.

“The Lath Console Table”
John Robert Portman 2011
60”x12”x34”
Pine, Cypress

Laths are long slender pieces of wood that are nailed horizontally between the studs of a house leaving narrow gaps in between strips so that the plaster of the walls and ceiling have something to adhere to when applied.  Lath and plaster work is a specialized building trade that is very labor intensive and requires considerable skill.  Since the invention of gypsum board, which is faster and cheaper to install than plaster, the use of lath and plaster in residential construction is very rare, even though its durability and quality is far greater than that of drywall.

As New Orleans is an old city, most of its houses were originally built with lath and plaster walls.  Since Katrina, the first thing a renovator does to a flooded home is to gut out all of the plaster and lath and discard it in a dumpster.  Because plaster is water resistant, the wooden lath behind the plaster is still in nearly the same condition as when it was installed, and thereby still usable.  A standard gutted shotgun house yields hundreds of wood lath strips.  This table is made from approximately 100 laths that have been fished out of dumpsters from all over New Orleans and re-purposed into a one-of-a-kind piece of furnitiure.

Built using traditional joinery, there are no nails or screws or fasteners of any kind holding the table together, only wood-to-wood connections.  The top is made by process of lamination, in which each individual strip is planed smooth and glued to another strip and another and so on.  The table top is connected to the legs via a through-wedged dovetail mortise and tenon joint, in which wedges are driven into slots cut into the end of the tenon.  The wedges expand the tenon within a trapezoidal-shaped mortise, thereby locking the tenon in place permanently (which is why this is also called a “suicide” joint).

The lath shelf underneath is connected to the legs by a square peg running though the legs and into a square hole chiseled into the shelf.  Even the pegs are made out of lathing strips.  The only non-lath part of the table are the legs, which are made of light-colored cypress in order to contrast the rich dark browns of the pine lath.

Leave a comment

Filed under Millwork, Salvage, tables, Uncategorized

Console table comission

I was recently commissioned to build another lathing strip table and work is well under way.  The picture below is of the top of the table.  More pics to come upon completion in about a week!

image

Leave a comment

Filed under Millwork, Salvage, tables, Uncategorized

Making a bracket

I had to make some copies of existing brackets that were damaged on a historic home in the Irish Chanel in New Orleans. I made them out of spanish cedar to resist moisture and cut them out on a scroll saw.

image

L'original.

image

The black stripes help me remember what is to be cut out.

image

scroll saws are perfect for bracket work because, unlike a band saw, you can detach the blade and thread it thru a hole to make isolated cuts in the center of a block.

image

image

once you have a good drawing to work from, all you need is transfer paper to copy the design onto wood.

image

The cutoffs all look like sea serpents to me.

I made three. Important that they all match!

1 Comment

Filed under Millwork, preservation, Presetvation resource center

Evil lamp unleashed.

image

Do-gooders of the world seeking hobbits to wage battle against sinister scarlet orb of doom. Please send resume with cover letter to Gandalf Pedersen, 1225 Shire Lane, Minas Tirith, M.E.

1 Comment

Filed under lamps, Millwork, Steampunk, Uncategorized

Evil Eye Lamp

image

I just bought a neato old light fixture on ebay with a red glass globe that I’ll turn into a table top lamp. It reminds me of a vintage movie house light with its soothing red color, but Leslie says it makes her think of the eye of Sauron (lord of the rings evil overlord) and is slightly afraid of it. Either way, there has to be a market out there for something like that, right? I can see the etsy listing now: “vintage scarlet orb of doom lamp for your desktop…”

Leave a comment

Filed under lamps, Salvage, Steampunk, Uncategorized